To Top

Hobart Welder 250 AMP Raleigh, NC **SOLD**

• CATEGORIES: Industrial-Welder-Generator This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1500.

Looks in good shape.

“250amp Hobart pull behind welder/generator has 4 cylinder jeep willys motor that runs great and welder and generator also work.. just been checked out ”

To Top

1954 Hobart Welder Custer Park, Illinois $1000

• CATEGORIES: News This site contains affiliate links for which I may be compensated.

This looks in good shape.

“1954 Hobart G200 D/C welder on trailer. Uses a CJ2A four cylinder Jeep engine. There is also a 120 volt outlet on the machine for running your power tools. The machine was just restored. Valves and valve seats were reconditioned, fuel and oil lines replaced, new belts, hoses and tune up parts. Generator bearings were repacked, brushes were replaced, radiator was cleaned and pressure checked. Body panels were stripped to bare metal and repainted with automotive paint. Machine was thoroughly tested and runs and welds perfect. Is ready to weld for another 56 years”

http://chicago.craigslist.org/sox/tls/3075585215.html

To Top

DC Welder/Generator Minneapolis, MN **SOLD**

• CATEGORIES: Industrial-Welder-Generator This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD* Was $250.

This might be a good price on a motor.

“An older Hobart 250 amp welding generator driven by the industrial version of the Willys 4-134 flathead engine used in the CJ-2a Jeep and the MB. Brush-type generator. Electrical side was working last time I ran it 5 years ago, but the engine uses oil badly and needs and overhaul. Parts are readily available but I have too many projects. See photos. Engine is complete with generator, carb, starter, fuel pump, and should run with minimal effort. The electrical side has the main DC welding output and also a 120v dc convenience outlet for a grinder or light. See the gray machine in the photos. Cables not included in sale. $250 as is where is or make offer. Loading and delivery available at reasonable rates.

Also for sale is the green 400 amp welder. This is driven by an electric motor. Machine dates from roughly the 1950s and works well but does require 3 phase A/C or a converter box. I ran it on a converter which works fine as long as you don’t run it at full output. $200 as is where is or make offer. Loading and delivery available at reasonable rates.”

To Top

Jeep Monument in Galleta Meadows Estate in California

• CATEGORIES: Artists/Drawings, Features, Monuments/Statues This site contains affiliate links for which I may be compensated.

According to the website, “Dennis Avery, land owner of Galleta Meadows Estates in Borrego Springs envisioned the idea of adding ‘free standing art’ to his property with original steel welded sculptures created by ‘Perris Jurassic Park’ owner/artist/welder Ricardo Breceda based in Perris, California.”  One of the sculptures he commissioned was a tribute to the jeep (or jeeping, I don’t have specific information about the sculpture).

You can learn more here

You can see a variety of jeep pictures here

These pictures were photographed by Bob Perry and posted at Flickr.  Note that there are no boulders under the jeep at the time they were taken in 2010.  However, as of 2012 there are now boulders, suggesting the jeep is climbing over them.

To Top

1954 Truck with Hobart Welder Joliet, IL **SOLD**

• CATEGORIES: Features, Industrial-Welder-Generator, trailer, Unusual, Willys Trucks • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE:  Was on eBay

(05/30/2012) This is a cool, well restored combo.

“HERE IS A SUPER NICE TOTALLY RESTORED 1954 JEEP 4X4 THIS JEEP IS A SHOW PIECE THAT COMES WITH A PERIOD CORRECT TOTALLY RESTORED HOBART GAS WELDER. LOOK AT THE PICS CLOSE, IF YOU WOULD LIKE TO SEE ANY OTHER PICS LET ME KNOW. THE BUY IT NOW IS BELOW MARKET VALUE  FOR THE JEEP. THE WELDER IS A SUPER RARE ITEM. THE JEEP RUNS GREAT, 4 WHEEL DRIVE WORKS PERFECT IN 4 HI AS WELL AS 4 LO.  JEEP CAME ORIGINALLY WITH RARE PTO. THE UNIT IS STILL WITH THE TRUCK. ALL THE GAUGES WORK,  WATER TEMP. OIL PRESSURE, AMP GAUGE. ALL BRAND NEW TIRES ON JEEP AS WELL AS WELDER.   THE WELDER IS A FACTORY GAS ENGINE WITH A JEEP WILLYS 4 CYL. ENGINE. IT RUNS GREAT AS WELL.  IT IS SUPER DETAILED AS YOU CAN SEE. PRIOR TO THE TOTAL RESTORATION OF IT THE WELDER PERFORMED FINE. I HAVE NOT TRIED TO WELD WITH IT SO THAT PART I AM NOT POSITIVE ABOUT. I  HAVE A FACTORY MANUAL THAT COMES WITH IT. I HAVE A GOOD DEPENDABLE GUY THAT TRANSPORTS FOR A VERY REASONABLE FEE,  IF THE WINNING BIDDER CONTACTS ME I WILL GIVE YOU HIS INFO. AND HE WILL GIVE YOU A PRICE ON GETTING THESE TO GEMS TO YOU ! THANKS FOR LOOKING, I DONT THINK YOU WASTED YOUR TIME !!! I AM NOT SURE ABOUT THE MILES”

To Top

Hobart Welder River, Az $1500

• CATEGORIES: Industrial-Welder-Generator This site contains affiliate links for which I may be compensated.

This is a really nice example of a hobart welder with the Willys Jeep Engine.

“Hobart AC/DC welder and generator[alternator] .
4 cyl willys engine
rectified DC
300 amps AC
300amps DC
generator,
2- 20amp, 220 volt
1-50amp,220 volt
4-15 amp.120 volt
total 27000 watts
Calls Only
Jerry
four15336-62one four”

http://tucson.craigslist.org/tls/3056642046.html

To Top

1954 Hobart Welder Custer Park, Illinois $1000

• CATEGORIES: Industrial-Welder-Generator This site contains affiliate links for which I may be compensated.

This has a CJ-2A L Head engine.

“1954 Hobart G200 D/C welder on trailer. Uses a CJ2A four cylinder Jeep engine. There is also a 120 volt outlet on the machine for running your power tools. The machine was just restored. Valves and valve seats were reconditioned, fuel and oil lines replaced, new belts, hoses and tune up parts. Generator bearings were repacked, brushes were replaced, radiator was cleaned and pressure checked. Body panels were stripped to bare metal and repainted with automotive paint. Machine was thoroughly tested and runs and welds perfect. Is ready to weld for another 56 years”

http://chicago.craigslist.org/sox/tls/3002507851.html

To Top

Jeep Collector’s Estate Sale Lowell, MI June 25-26

• CATEGORIES: News This site contains affiliate links for which I may be compensated.

No pics provided.  It sounds like lots of stuff.

“Jeep Part Collectors Estate Sale June 25 and 26th. Sale will be held at 1650 Foreman Rd Lowell MI 49331

In addition to the parts there is a large collection of tools ( such as saws, hammers craftman tools, chains, car hauling equipment, Stihl chain saw, carts, garage equipment, oil, filters, welder, jacks, stands, wood, steel, comercial lawn mower, residential lawn mower w/ rototiller and deck attachments, Antique furnature, Wood Burner, 50+ glass blocks and much more to come
.
CJ, XJ, YJ, DJ, Cherokee, Comanchee, FSJ, TJ, YJ and Willys parts.
To many parts to list. Collection has been gathered over the last 30 years.
DJ and CJ:
Rear swinging DJ doors, Dash assemblys, steering boxes, Pedal assemblys, Steering colums, Heater assemblys, Wiring, filters, Transmissions, AMC V8’s, Transfer cases, Drive shafts, Axles, Alternators, Tires, Wheels, Tailgates, Glass components, Roll bars, Lenses, Headlights and buckets, starters and much more.
FSJ:
Gladiator Axles, Radiators, steering box’s, filters, Every piece of glass you can imagine, Steering Colums, Wiring, Trasmissions, Fenders, Heater assmeblys, Starters, Alternators, Drive shafts and much more.
XJ and Comanchee:
Grilles, Tires, Wheels,Fog lights, Comanchee tailgate (almost rust free, only surface rust in one spot) and more
TJ:
Tires, Wheels, Tranny pan, 2004 Jeep Wrangler Right hand steer postal Jeep and more
Willys:
Many Misc interior components, Wiring, rear lift gate for wagon, Trim pieces, OE pieces still in box’s and more.

Still sorting through it all. No Pre sales. Cash only. More info to follow. Times to follow however I believe it will start in the morning each day around 9 or 10. Hope to see you then.”

http://grandrapids.craigslist.org/gms/1785974079.html

To Top

Hobart Welder Gunlock, Ut $500

• CATEGORIES: Industrial-Welder-Generator, Machinery, Unusual This site contains affiliate links for which I may be compensated.

Brett spotted this Welder.  These are usually priced between $800 – $1200, so this appears to be a good price (if the fix is easy).

“Hobart Welder. 250 Amp 40 Volt. Willys engine. Welder was not making power when machine was parked. But the Willys jeep engine still ran. no emails. Please call 435-632-2415”

http://www.ksl.com/?nid=218&ad=10401670&cat=&lpid=

To Top

Year? Jeepster Ripon, Ca Make Offer

• CATEGORIES: Jeepster This site contains affiliate links for which I may be compensated.

It looks like some hard work has been completed on this project.

“Body Work done, Lost Interest. Will consider trade for the following; Mig Welder, Large Tool Box and etc., Cash Offer. Let me know what you have? Call me 209-599-1640 or email me for more pictures at anthonymanda@gmail.com.”

http://modesto.craigslist.org/cto/1529851452.html

year_jeepster_ripon

To Top

Valentine APU CJ-3As Shipshewana, **Sold**

• CATEGORIES: CJ-3A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **Sold**

Nick is selling his very rare Valentine-built CJ-3A APUs. He’s done a great job of uncovering the history of these Valentine APUs and sharing it with the jeep community.”

valentine-cj3a-apu-in

“These Willy-Overland CJ-3A utility vehicles were converted into auxiliary power units for the US Navy in the 1950s by the Valentine Welder & Manufacturing Company for use in starting jet aircraft engines. Both vehicles are finished in yellow and equipped with a seven-slot grille, flat front fenders, a single-seat operator’s station, and power take-off equipment. The pair includes an NC-2 mobile power plant that was designed for use on aircraft carriers and modified with rear-wheel steering, front-wheel drive, and a rear equipment platform. The other truck is one of approximately 75 such units modified into an NA-4 ground-based mobile APU and is fitted with a replacement Willys F-134 inline-four paired with a three-speed manual transmission. The engine has been removed from the NC-2 and is included in the sale.”

To Top

1946 CJ-2A Cedar Rapids, IA $10,000

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Price dropped to $10,000.

(05/25/2021) Is there a little rust along the driver’s side? I can’t tell for sure.

https://www.facebook.com/marketplace/item/1457334221741766

1946-cj2a-cedarrapids-ia6 1946-cj2a-cedarrapids-ia7 1946-cj2a-cedarrapids-ia8 1946-cj2a-cedarrapids-ia9

“***I am helping a friend sell this, please be patient and I will answer questions as I am able to relay them and get a response*** VIN: 38222 1946 Jeep Willys CJ2A 77 year old vehicle in fantastic condition has minor dings here and there but no major dents or damage to body or frame. Has some surface rust on undercarriage as shown. Needs a little TLC and can be a great winter project. Starts every time, but can be a little touchy with a one barrel carburetor. Numbers matching engine, original dash information tags included. Mostly original except basic maintenance items. Also unsure about the paint being original. Unlikely, unless the paint is very faded because research suggests the factory blue would’ve been much darker. New battery in 2019, whole fuel system replaced, fuel filter, fuel tank all done by Hubbell’s Auto Repair in Marion, IA. Had professional welder check over undercarriage and did frame brace welding work. Factory storage bin under passenger seat was professionally refabricated and welded by the same welder and he did a great job. Factory bikini top included. Originally 6V converted to 12V prior

To Top

Year? M-38 Asher, OK $2500

• CATEGORIES: M-38 This site contains affiliate links for which I may be compensated.

Unclear how much value is here. It has a variety of updates.

https://www.facebook.com/marketplace/item/500061095350066

“PLEASE TEXT MY SON ITS HIS 4o5-287-477o 1955 Willy’s jeep Got it in trade Has a Chevy inline 6 cylinder with twin stick t case Motor does run on gas jug Needs rewired No title Has motor, trans, and transfer case Has some rust but not terrible it’s old and been hacked on to fit motor 2500 OBO or trade for Toyota, samurai, etc trade for Chevy square body or obs or Gbody Tools, welder, trailer, man stuff”

year-cj-asher-ok5 year-cj-asher-ok6 year-cj-asher-ok7 year-cj-asher-ok8 year-cj-asher-ok9

To Top

Repairs To the Front Frame Rails

• CATEGORIES: Features, videos This site contains affiliate links for which I may be compensated.

Roger shared this Youtube video by RowdyWelder who shares how he rebuilt the badly damaged front frames rails on this old jeep.

To Top

1948 CJ-2A Del Mar, CA $13,500

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

The jeep appears solid, though the drain holes have been filled, so the body should be checked for filler. This has an f-head and custom hood. There are additional mods.

https://sandiego.craigslist.org/nsd/cto/d/solana-beach-1948-willys-cj2-jeep-new/7532324944.html

1948-cj2a-delmar-cali6 1948-cj2a-delmar-cali7 1948-cj2a-delmar-cali8 1948-cj2a-delmar-cali9

“Bought off Bring a Trailer for $11k over a year ago and was told it was in perfect shape, guess what and no surprise, that good old boy from Virginia lied through his teeth!!!

Anyways, I’ve had several Jeeps and this one has one of the nicest rust-free bodies, as well as complete and original gauges, E-Brake Handle, Seats, Motor and Trans. The engine has been completely rebuilt by a top shelf mechanic that works on my entire collection of rare and High cars such as Porsches, Mercedes, and muscle cars. I bought this as a beach cruiser, around, town summer fun car…
Continue reading

To Top

1942 MB? Eagle Point, OR **SOLD**

• CATEGORIES: MB This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $10,000.

Lots of updates to this rig.

“1942 jeep rock crawler. Small block Chevy T18. 4 speed with overdrive. Dana 4×4 axles. Detroit locker and arb locker. 513 gears. Has air compressor, welder on board. Warn winch, tow bar, stereo, speakers, cb radio. Extra parts like axels, drive lines, u joints. Runs good. May entertain trades in”

1942-mb-eaglepoint-or0 1942-mb-eaglepoint-or1 1942-mb-eaglepoint-or2 1942-mb-eaglepoint-or3 1942-mb-eaglepoint-or4

To Top

Racer Work Resumes…

• CATEGORIES: Features • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Today I removed the tube bender from its box, only to find that the collar for the tube bender had irregular holes that had been “patched” by welding two spacers to the outside of it. But, that modification meant that the bolt was no long enough, meaning one of the two sides of the collar would be riding over the threads. Given the importance of the collar, this “fix” is unacceptable, so this bender will get returned.

Below you can see that both holes are irregular, so a spacer has been welded to the outside. What are these people thinking? 
affordable-bender-collar2 affordable-bender-collar1

affordable-bender-collar3

The bolt next to the collar is the stock bolt. I happened to have a similar bolt that was longer and better for this application. However, given the poor quality collar, I will be returning this device.

============================

As mentioned, a couple weeks ago we had the estate sale, which consumed WAY too much of my time. First there was the setup. Then, there was the rain, so then we had to re-setup using part of the shop (which meant moving stuff out of the shop like the race jeep), hanging tarps to hide tools, etc. In the end, the rain stopped Saturday at 4am and began Sunday at 3pm, which gave us a decent window to sell stuff.

We sold or gave away quite a bit, but there were still multiple trips to donation centers, a trip to recycling, and several trips to the dump. Then, once completed, we still had to reorganize the remainder.

The good news is that a lot of crap left the shop, which gives me much more room than I’ve had. Also. good news, the weather has finally warmed up, with blue sky and no rain.

So, I finally returned to work on the racer, though the work was mostly grinding/cutting off the remaining pieces of the rear front spring holders and the former mounts of the side bars. With that done, I can now fit the new side bars.

Before:

2022-06-25-race-jeep-grinding-before

After:

2022-06-25-race-jeep-grinding

I’d prefer to take the whole thing apart to better clean up and paint the frame, but that can wait until winter. For now, I am focusing on functionality over style (though the green will be painted black before the body is installed).

With the grinding done, I’m not far from being able to begin work on the roll cage. The new cage will be wider (for the wider Parkette body) and roomier (so I fit better). To build the cage I needed to get some new tools.

My plasma cutter arrived a few days ago, along with my tube bender (from Affordable Bender). I was going to build another bender, but I cannot locate printed copies of my bender plans nor can I find the password to the PDF I received from gotTrikes.com (locked PDF .. and no response from the gotTrikes website for a new password). So, after some research, I decided to take a chance on the AffordableBender, which as gotten pretty good reviews.

The thing I am awaiting now is my new MIG welder, which was supposed to arrive around June the 9th. It is now expected to arrive June 29th.

To Top

Progress on the Racer

• CATEGORIES: Features, Racing • TAGS: This site contains affiliate links for which I may be compensated.

On Sunday I turned 57. The years seem to be churning by all too quickly! To celebrate my aging, I spent more time removing parts off both the green chassis and the black chassis (no updated pics of that). While spending time thinking and measuring how to use as much of the existing green chassis and black chassis parts as I can, I made an unexpected discovery.

The green chassis is 5 inches wider than the black chassis!. The black chassis is a standard size (29.5″ from inner side to inner side) and seems to be most likely a CJ-3A chassis. The green chassis has the side mounts for the springs and was most likely a DJ-5 chassis as some point. For whatever reason, someone decided the frame rails should be widened, so all the crossmembers were removed but one (which was simply cut and patched using angle iron). The rest of the cross members are all rectangular tubing.

Given the widening, I don’t feel the need to outboard the rear springs at this time (perhaps a winter project). Unfortunately, the wider frame rails mean that I can’t just reuse the sway bar on the back of the black chassis (though I can reuse the mounts). I just need a sway bar that is 5″ wider than the one I have.

I am awaiting the delivery of an adapter so I can try out my new YesWelder plasma cutter to clean up more of the frame and am awaiting delivery of my new MIG Hobart MVP 210 Welder (I have a very very old arc welder that’s a big workhorse on heavy metal, but I wanted something for finer work). I had considered something as cheap as the YesWelder MIG (it is well-rated, but some folks complained about support problems) and something pricier as the Miller Multimatic 215 (which came highly recommended, but may be more than I need right now), but finally decided to get something more in between.

Anyway, here are a few pics of the progress. There’s nothing particularly exciting .. just the drudgery of cutting, grinding, and smoothing areas …

The seat mounting frame (1″x1″) tubing was uneven and not the best system in my opinion, so I cut and grounded the welds flat:

2022-06-06-parkette-racer-pics1-lores

With the seat mount frame gone, you can see the floor base (also 1″x1″ square tube). It’s not welded level (ugh), so it will likely go away as well.

2022-06-06-parkette-racer-pics2-lores

The side rails needed to be replaced as they were built for the narrower body, so off they came. I also plan to do a side bar similar to the way the other frame is done (more on that later).

Also gone are the mud flaps on the back (racing requirement), as they were welded onto the inside of the rear tubes (ugh). I will cover the rear tube with plates to hide the parts welded inside, then will cut off and mount the flap system used on the other frame, which is a long tube welded under the rear bumper with flap mounts that are bolted onto the tube (again, more on that later).

2022-06-06-parkette-racer-pics3-lores

We plan to have a garage/estate sale this weekend, so work will slow for a few days. At least I will finally be able to get rid of a bunch of junk that has filled the shop. As Ann has been finalizing stuff in the house, more items have ended up in the shop, so I will be happy to have this stuff gone and have more room to work.

Finally, I am awaiting a new fuel pump for Patterson (which has taken more than 2 weeks to get here). Once that is here, I will test things out once more, then put Patterson up for sale (essentially trading up for a different jeep, but I will announce that later).

 

 

To Top

1953 CJ-3B Dually/Auger Phoenix, AZ $4000

• CATEGORIES: Unusual • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Price dropped to $4000.

(01/03/2022) This is a big, unusual project. I might have posted this when it was first listed, but I can’t locate it at the moment.

https://www.facebook.com/marketplace/item/612314290077474

21953-cj3b-dually-auger-phoenix-az 1953-cj3b-dually-auger-phoenix-az3 1953-cj3b-dually-auger-phoenix-az4 1953-cj3b-dually-auger-phoenix-az5

“This Jeep was sitting for many years. It was an auger during its working life. I got it from a guy who installed fences along property lines in Apache County in Arizona’s White Mountains, intending to get it running but it became a project that went to the back burner.

I took the head off to see why the engine did not turn completely over and discovered that one of the valves is stuck. The cylinders are smooth and free of any scoring and the pistons move freely up until the point where the valve sticks. The Jeep was down due to a broken gear in the auger’s drive mechanism not because there was a problem with the engine or transmission. The original F head engine had been swapped out with a CJ2A L head engine.

I bought a bunch of parts for it. I have a replacement starter, distributor, carburetor, rear drivers side brake drum(already installed), master cylinder, brake lines, wheel cylinders and rebuild kits, shift knobs and rubber boots, etc. I even bought a new 6 volt battery for it but never installed and now due to sitting, it fails to hold a charge. It may be salvageable by opening the case and desulfering it. They are all included. All the parts for the auger are there including the broken pinion gear that needs to have the broken teeth built up or a new gear made up.I am selling it as is as I do not have the time to continue it.
Continue reading

To Top

1946 Fortune Article on Willys-Overland

• CATEGORIES: Features, Magazine This site contains affiliate links for which I may be compensated.

UPDATE: This post was published on eWillys November 15, 2014. I don’t normally post whole articles, but there is a great deal of interesting information within it. I’m reposting this today because there is some additional information about Mr. Clement Miniger and his Auto-Lite company leading a syndicate to buyout John North Willys’ stock in 1929 (Learn more about Miniger And Willys Light here).

1946-08-fortune-mag-pg81-closeup-jeeps

A variety of pre August 1946 CJ-2As in different colors waiting to be shipped from Willys-Overland’s Toledo plant.

This fascinating article was published in the August 1946 issue of Fortune magazine. It’s a LONG article that covers the history of Willys Overland Corporation from it’s bankruptcy in the early 1930s to it’s post-war market positioning. There is not much information specifically about jeeps, nor many jeeps photos. But, if you want to understand how the corporate structure evolved, it’s a good article.

One particular chart published in the article was Willys’ research on paved roads. The company felt that jeeps would be very popular in outer countries, due both to the brand and the lack of paved roads. To meet that demand, Willys planned to export 25% of all jeeps.

1946-08-fortune-mag-pg80-building-lores 

WILLYS-OVERLAND

THIS JEEP-RIDING AUTO INDEPENDENT IS TAKING NEW LEASES ON LIFE AND ITS OWN REAL ESTATE • THE BOYS IN THE BACK ROOM ARE DOING FINE

ln the years between the depression and the second world war, the once great Willys-Overland Co. clung by its nails to a niche in the U.S. automobile market. Gamely, it tried to sell the public a mousy little car, with a tough, four-cylinder engine, which was the cheapest thing on the road to run. Itself battered into receivership and reorganization by the depression, Willys had the patently sensible idea that such a car, guaranteed to get people from here to there at a minimum expenditure for fuel and upkeep, would be a blessing to a hard-pressed public that had not been similarly served since the demise of the models T and A Ford. But the public was proud, if poor, and more conscious of the millinery than the engineering of a car. When it had to buy cheaply it found the used-car market much more tempting. During most of those years Willys’ production ranged below the break-even point. bln 1940, a mere 27,000 cars were built. Now Willys-Uverland is coming up for the postwar round with a product line still topped by a light passenger car-with a four or a six-cylinder engine, buyer’s choice. It will probably be as cheap to buy, give or take a few dollars, as any 1947 car on the market, and possibly less expensive to operate and support than any of its competitors. And though it will be considerably more stylish, inside and out, than the prewar Willys, it will have, at most, simple good looks rather than breath-taking beauty. If that were the whole story, one might wonder why some people think Willys-Overland is an exciting proposition among the auto independents today, and why some mighty big boys in the automobile industry appear to be sparring for position in the peculiar, complicated Willys-Overland hierarchy.

Unquestionably Willys has fresh charms. To name four:
1) The tough, four-cylinder motor that was the bread-and-butter item in the prewar Willys is the same motor that powered the Army Jeep, which became an international byword during the war. As the largest producer, by far, of the Jeep, Willys-Overland became the beneficiary of this enormous, war-born prestige (and also added a tidy sum to its treasury). Ten days after V-J day, Willys was in production on its civilian or Universal Jeep, of which it had sold around 28,000 by June 1, despite plant shutdowns totaling eighty-three days owing to strikes in suppliers’ plants.

2) Under way at its giant Toledo plant is a Jeep-inspired line of Willys utility vehicles including (a) an all-steel, all-purpose station wagon, (b) a sedan delivery truck, and (c) a low-weight, medium-duty truck with a combination four and two-wheel drive. All are powered by an improved four-cylinder Jeep engine and feature the Jeep snub nose and square fenders. All will be produced in 1946, and can be run through the same assembly line if necessary.

3) Because the rugged, lightweight vehicles in the Willys line are peculiarly suited to the exigencies of foreign motoring, in which the paucity of paved roads and the steep price of gasoline are forbidding factors, the company has decided to throw 25 per cent of its production into export. The development of a foreign market of such proportions is steadying to the seasonal economy of an automobile company. And Willys’ new top management is richly experienced in the export field.

4) Finally, many an economist, foreseeing an era of inflation, high taxes, and high gasoline costs, will agree that the hour in the oiiing is ripe for an automobile that places operating economy above fashion appeal. Willys is confident that its traditional economy car is, at last, accurately attuned to the times, and that its 1947 passenger model can bite into a solid and sustained market, both here and abroad.

Continue reading

To Top

1951 CJ-3A Tustin, CA **SOLD**

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3000.

(11/20/2020) Looks like a full rebuild that will take more effort than the seller suggests.

“Check out this sweet 1951 cj3a. She has a very solid body. Bubba cut a 2 holes in the rear. I’m guessing to use so kind of equipment. Mobile welder or something off a PTO. She was a work jeep for sure. But looks to be taken care off. Other then the hood the body has this cool German desert camo kind of patina too it and check out the vintage mascot painted one it. It says “go devil powered” pretty Rad!! Also on the tail gate you can still make out the willys four wheel drive. I have a windshield frame gas tank and radiator for it. As is. has a tile and non op reg. But she has her spot in line to be fixed up and it won’t take much to get her going and street worthy again!!”

1951-cj3a-tustin-ca0 1951-cj3a-tustin-ca1 1951-cj3a-tustin-ca2 1951-cj3a-tustin-ca3 1951-cj3a-tustin-ca4

To Top

Anyone Recognize Tracy’s 1944 MB

• CATEGORIES: Builds, Features, Sedan-jeep • TAGS: This site contains affiliate links for which I may be compensated.

Tracy shared pics of his grandfather’s WW2 jeep that was customized at some point, either motor-pool modified or post-war modified. He’s hoping someone might have more information about it.

1944-mb-tracy7

1944-mb-tracy1“This Willys came to me by way of my grandfather, a WW2 veteran of Normandy where, D-Day+1 his unit was shelled by 88’s and he lost his leg.

I have no idea when he, himself, acquired it as I never even knew it existed until I was called to remove it. Since my father never mentioned it to me, it is likely he didnt know either.

I can only assume he had visions of restoring it. Now, that falls to me, and I gladly accept that.

My plan is to do more of a “restification” on it than an all out restoration.

You see, the modifications that have been made are completely, and thoroughly welded in place. As it looks to have been this way since, at least, the era that it was acquired as surplus, if not before, it has really become part of the vehicle’s story and it will remain. The workmanship is very well done and, whoever did these modifications was a very skilled welder/fabricator as all welds, fit, and finish are top notch.

So, I share it here in hopes that I may find information on that history.”

1944-mb-tracy2

1944-mb-tracy3 Continue reading