To Top

1948 CJ-2A Edwardsville, MO $12,500

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

Lots of updates.

“Coolest Willys jeep around. Frame off restoration. Titled 1948 cj2a
Body is rust free. Replaced floor and added 2×2 box tube supports
1986 mustang gt crate motor. Still has break in oil. Less than 200 miles on motor
T18
Dana 18 transfer case
90″ wheelbase
Dana 44 front axle Detroit locker 4:56 gears
35 spline Spyder 9″ rear axle Detroit locker 4:56 gears
35×12.5×15 Brand new Goodyear MTRs
M38 grille
Front tube fenders
Full rocker guards
Hood stretched
Allied bead locks
Anti Rock sway bar
PRP seats with harnesses
Full roll cage
Relocated gas tank to the rear
New exhaust
Raptor lined inside and on the bottom
Has military hard top, I have an old soft top frame and doors.
This thing is awesome to drive! I’m only selling to buy my daughter a car. I have brand new warn hubs that I haven’t put on, along with the front driveshaft. If I get to them, I will put them on. Have a heater but haven’t put it back in yet either. I also have all the grab handles, shovel and axle holders to make it look like military. May take a partial trade on a nice compact car.”

http://stlouis.craigslist.org/cto/5981041484.html

1948-cj2a-edwardsville-mo1 1948-cj2a-edwardsville-mo2 1948-cj2a-edwardsville-mo3 1948-cj2a-edwardsville-mo4

 
To Top

1947 CJ-2A Santa Rosa, CA $3000

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: Still Available.

(12/13/2016) Needs a little more work of some kind.

“90% complete
Buick v-6. 3speed trans with overdrive
New gas tank. New floor. Completely bed lined
New front bumper with 6000lb winch
Full gage roll bar
Street legal lincenced with clear title
Runs but hard to start in the morning. Might be a fuel pump
May have a head gasket leak. Oil is a little murky”

http://sfbay.craigslist.org/nby/cto/5979943657.html

1947-cj2a-santarosa-ca001 1947-cj2a-santarosa-ca002

 
To Top

1947 CJ-2A Mustang, OK **SOLD**

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $2000. May have Watson hubs.

Could use some paint.

“Runs and drives and is tagged.
1947 very rare”

1947-cj2a-mustang-ok41 1947-cj2a-mustang-ok42 1947-cj2a-mustang-ok43 1947-cj2a-mustang-ok49

 
To Top

1947 CJ-2A Liberty, MO $6250

• CATEGORIES: CJ-2A • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: Price dropped to $5900.

(10/24/2016) Could use some better pics.

“Runs great, New tires, new water pump, new fuel pump.
3 speed, 4 wd
can text better pics if you want.”

http://kansascity.craigslist.org/cto/5975076583.html

1947-cj2a-liberty-mo1 1947-cj2a-liberty-mo2

 
To Top

1954 CJ-3B Detroit, MI $1800

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

Been stored for a couple decades.

“Jeep cj3b willys, this has the larger f head motor, been stored in barn for at least the last 25 years, I have no time to work on it. I have not tried to start it and would not try until fuel system is cleaned out. I got this from my grandfather who used it for years on the farm for hauling wood. Parked it after he had more wood then he could use, and never needed to use it again”

http://detroit.craigslist.org/mcb/cto/5977269021.html

1954-cj3b-detroit-mi-93 1954-cj3b-detroit-mi-94

 
To Top

Year? CJ-3A St. Louis, MO $750

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

That’s one of the taller hood bumps we’ve seen.

“Old jeep Willys with no title so unsure of year. Has new starter and a few other parts. Carb is messed up and jeep won’t run right. Clutch is also not working but I think that’s just a broken return spring. This is a project off road toy only.”

http://stlouis.craigslist.org/cto/5977007696.html

year-cj3a-stlouis-mo2 year-cj3a-stlouis-mo3 year-cj3a-stlouis-mo4

 
To Top

1944 GPW Rancho Cucamonga, CA $5500

• CATEGORIES: GPW (Ford MB) This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $5500. Andy pointed out that this one had an Esslingen rebuild tag:

esslingen

ORIGINAL POST:

“Original 1944 Ford Gpw willys jeep. Needs restore. Has a WWII 1942 Gpw engine. The frame is a 1944 Gpw. parked since 1992 non op. Still has oil and water in the jeep. Had a blown head gasket when parked. Motor turns over by hand easily.”

1944-gpw-ie-cali1

1944-gpw-ie-cali2

1944-gpw-ie-cali3

1944-gpw-ie-cali4

 
To Top

Year? CJ-5 Maine Make Offer

• CATEGORIES: CJ5 • TAGS: This site contains affiliate links for which I may be compensated.

This has a Meyer hardtop.

“We have an old Willys Jeep 4×4 with a plow. This is very old (possibly 1960 but not entirely sure). It needs lots of love. It still runs (with a jump at this time) and it has a plow attached to it. Not for road use at this time. It is old and it is rough but like I said, the engine still runs. My dad used this to plow his yard until this year. You will have to haul it off yourself. Make an offer.”

http://maine.craigslist.org/cto/5980866867.html

year-cj5-me

 
To Top

Aluminum Koenig Hardtop Wichita, KS $75

• CATEGORIES: Parts • TAGS: This site contains affiliate links for which I may be compensated.

Appears to be missing windows and doors.

“1949 Willys Jeep for sale, needs finished up. has new transmission and clutch, reman head, new distributor and starter, its not far from being done but I don’t have time to finish and have to have surgery so its time to let someone else take over. this jeep has a fiberglass tub so it will never rust. frame is in great condition not rusty. need to see in person.”

http://wichita.craigslist.org/pts/5980515293.html

koenig-aluminum-hardtop

 
To Top

1949 CJ-3A Greeneville, TN **SOLD**

• CATEGORIES: CJ-3A This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3400

(12/22/2016) May be worth a look.

“I have for sale a 1949 Willys CJ3A. Runs, drives, 4-wheel drive good. Original 6V system with the L-head engine. Must see and drive. Perfect for the person that would like to complete the project or drive as is. Great hunting, farm vehicle or for leisurely drives. I have worked on this for the past 2 years starting from the ground up. Had lots of fun with it, just no longer interested in finishing it. Asking $3400.00. Text and I can send video of it being drove. Thanks”

1949-cj3a-greeneville-tn

 
To Top

1947 CJ-3A Tri Cities, TN $2800

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

UPDATE: Still Available.

(01/11/2017) Includes a Warn winch.

“1947 Jeep WILLIES
8000 POUND WARREN WINCH
RUNS GOOD, HAS NOT BEEN DROVE IN AWHILE – BEEN KEPT IN A BARN FOR MANY YEARS.
4CYL, DESCENT TIRES,”

http://tricities.craigslist.org/cto/5947321362.html

1947-cj2a-tricities-tn1

1947-cj2a-tricities-tn2

 

 
To Top

1954 M-38A1(?) Tripoli, WI **SOLD**

• CATEGORIES: CJ5, M-38A1 • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $1600.

(12/15/2016) Has a fiberglass body that looks pretty new.

“fiberglass body. Steel half cab and doors. Engine is out and needs to be rebuilt. No title. cash only pick up only”

1954-m38a1-tripoli1 1954-m38a1-tripoli2

 
To Top

1944? Wagon JeepRod Chico, CA **SOLD**

• CATEGORIES: Jeep Rods, Willys Wagons • TAGS: , This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $22,500

(08/16/2016) Nice looking ride.

“This is not a $50,000 car. It is an old school hot rod built by professional Jim Beechler, Fantastic freeway ride and a fun show car with several trophies. Its a driver.
454 Chev, ram-air with dual quads, Turbo 400
8″ Ford rear end
Mustang II front end
Jag headlights
Chopped, channeled, tubbed, z’ed, suicides, you get the idea.”

1944-wagon-jeeprod-chico-ca1 1944-wagon-jeeprod-chico-ca2 1944-wagon-jeeprod-chico-ca3 1944-wagon-jeeprod-chico-ca4

 
To Top

1958 CJ-3B Wesson, MS **SOLD**

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

UPDATE:**SOLD** Was $1000.

(11/18/2016) Unsure how much value is here.

“Mostly complete. Was running. Sat up. I think the valves are stuck. Have title.”

1958-cj3b-wesson-ms1 1958-cj3b-wesson-ms2 1958-cj3b-wesson-ms3

 
To Top

Paul’s Putting on Powder

• CATEGORIES: Builds, Features • TAGS: This site contains affiliate links for which I may be compensated.

Take it away Paul ….

For the past couple of weeks I’ve been disassembling, cleaning, bead blasting and repairing parts for the little Willys and the M100 trailer so they would be ready to be powder coated.  I still need to install new wheel studs in the hub flanges along with pressing in the new bearing races but that task should be finished tomorrow.  The driveshafts need one to be shortened and one to be lengthened before they’ll go to the powder coater but progress is being made.

paul-powder-coating7

The blast cabinet is 48 inches wide overall and the axle is slightly over 53 inches long so I had a bit of a problem fitting the axle in the blaster and still having room to clean the rusty steel.  My solution was to leave the side door open and block the opening with multiple layers of cardboard (taped to the cabinet)  with a hole cut slightly larger in diameter than the brake backing plate mount on the axle to allow movement of the axle during blasting.  

Before I began blasting I added two more pieces of cardboard (cut to fit snug around the axle tube) to cover the larger hole in the cardboard end cover.  With this cardboard and duct tape combination I was able to carefully blast two thirds of the axle without filling the air with glass bead dust.  Once the axle section in the cabinet was clean I removed the axle, turned it end for end and inserted the rusty end into the cabinet to finish cleaning the metal.  This photo shows the low tech cardboard and cheap duct tape alteration of the blast cabinet so the axle blasting could begin.

paul-powder-coating6

The air compressor was blowing lots of air but the glass beads still had to work pretty hard to clean all of the rust off this 65 year old axle.  The metal is lightly pitted (especially on the forward side) but I don’t feel the original strength of the axle has been weakened in any way.  I checked the axle and the spindles with a straight edge and a level every 90 degrees of rotation to see if it was bent but the axle tube and the spindles are straight.

paul-powder-coating5

Here’s the axle just out of the blast cabinet ready to visit the powder coaters where it will receive a nice satin black coating.

paul-powder-coating4

Continue reading

 
To Top

1951 M-38 Phoenix, AZ **SOLD**

• CATEGORIES: M-38 This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $7000.

“1951 M-38, reproduction CJ3A body, original engine with Solex carb, transmission and transfer case in excellent condition. Original front and rear axles, new springs front and rear, upgraded seats, new tires and spoke wheels with 0 miles, new dash gauges, custom front bumper, new windshield glass. Drives and runs great. $7,000.”

lee's Jeep 009

lee's Jeep 010

lee's Jeep 011

Misc photos 2012 016

 
To Top

1952 Truck Cleburne, TX **SOLD**

• CATEGORIES: Willys Trucks • TAGS: This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $4300.

May be a good price.

“1952 Willy 4 by 4 pickup rare find very rare running driving Motors been redone training shifts like butter brakes have new lines and new wiring from 6 to 12 volt I drive it all the time”

1952-truck-cleburne-tx1 1952-truck-cleburne-tx2 1952-truck-cleburne-tx3 1952-truck-cleburne-tx4

 
To Top

1954 Model? Eagle, CO $1500

• CATEGORIES: CJ-3B This site contains affiliate links for which I may be compensated.

Seth says he could take a look if anyone is interested. Below is the ad’s text. He spotted it on a FB Group page.

“If you’ve ever wanted a Jeep here is your chance. It was fully rebuilt and running like a champ. Then lost in a bet and sadly sat for a while. I picked it up with dreams of making it a beast. I have realized that I don’t have the time to make it what I want. It needs a gear head to crank on it and it will run like a champ. I will take $1000 cash or we can make a deal.”

FB_IMG_1485601497448

 

 
To Top

1951 Truck East Moline, IL **SOLD**

• CATEGORIES: Willys Trucks This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $15,000.

Interesting build. The body fits pretty well.

“elling 51 Willy,s 4×4 2000 Silverado doner truck 5.3 ls motor 4l60e trans power steering & brakes new interior costom front bumper with built in winch some new glass drive & have fun”

1951-truck-eastmoline-il1 1951-truck-eastmoline-il2 1951-truck-eastmoline-il3 1951-truck-eastmoline-il4

 
To Top

1962 Jeep Rod Truck Los Angeles, CA $13,000

• CATEGORIES: Jeep Rods, Willys Trucks This site contains affiliate links for which I may be compensated.

Lots of custom here.

“This is a completed project that took us a year to built. This is a true Rat Rod.
The chassis is a 1962 Willys pickup truck with all stock parts.
The engine is a brand new V8 Chevy 327 small block with 350 HP.
Everything is in a perfect running condition. No repairs or modifications needed at all. The truck is ready to drive.
Pink slip in hand, no late fees, car is registered with the DMV and has insurance and
registration is already paid for 2017.

Here’s a full list with the trucks specs and accessories:

Taylor aluminum battery box.
Taylor aluminum gas tank.
New 1962 Bolt together chassis kit for front and rear suspensions.
New rear 19 inches rims with new Continental tubeless racing tyres. 265mm
Front stock 16 inches rims with Nylon Hot Rod tyres.
New Ford 1932 aluminum radiator from Speedway motors.
New 13 inches electrical radiator fan from Speedway motors.
New 13 inches aluminum fan shroud from Speedway motors.
New front disc brakes with 10 PSI Wilwood brake T valves.
New rear drum brakes with 10 PSI Wilwood brake T valves.
New stainless steel 36 inches rods for engine support.
New power steering system from Speedway motors.
New Chevy alternator.
New 1932 Ford Distributor kit from Speedway motors.
All the cable wiring made with enhanced extra thick cables from Speedway motors.”

http://losangeles.craigslist.org/lac/cto/5971242288.html

1962-jeeprod-truck-la1 1962-jeeprod-truck-la2 1962-jeeprod-truck-la3 1962-jeeprod-truck-la4

 
To Top

1946 CJ-2A Missoula, MT $4000

• CATEGORIES: CJ-2A This site contains affiliate links for which I may be compensated.

It runs and drives, but needs a little work. Looks solid.

“Looking for a project? Look no further this willys cj2a is what you are looking for. Runs and drives but needs work. Pretty much all original. The body is in good condition very little rust. Its been in a garage. Motor needs work it leaks oil dryed out seals I think. I just dont have the time or desire to put in the work. There is no title. The guy i bought it from didnt have one”

http://missoula.craigslist.org/cto/5975071879.html

1946-cj2a-missoula-mt1 1946-cj2a-missoula-mt2

 
To Top

1949 Jeepster Norwalk, CT **SOLD**

• CATEGORIES: Jeepster This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6500.

(11/14/2016) Seller notes it needs finishing, but doesn’t indicate what it needs.

“1949 willies runs good no rust
Needs finishing”

1949-jeepster-norwalk-ct1 1949-jeepster-norwalk-ct2 1949-jeepster-norwalk-ct3 1949-jeepster-norwalk-ct4

 
To Top

1976 DJ-5 Anacortes, WA **SOLD**

• CATEGORIES: DJ-5 & DJ-6 This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** WAS $1700.

(12/26/2016) It includes the ice cream box.

“1976 right hand drive mail Jeep runs great has new brakes new shocks comes with freezer and music box it is ready to sell ice cream this is a great small business to make some quick cash”

1976-dj5-anacortes-wa

 
To Top

1957 FC-150 Fillmore, CA **SOLD**

• CATEGORIES: FC150-FC170-M677 This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $6000.

(12/07/2016) It has some updates, but has sat a while. Engine will start.

“This is a clean straight rare and desirable fc150. Been in our family since 1974. In the late 70s the engine was updated to a 327 chevy with adapter plate so the rest is still jeep drivetrain. Has not run in years but will.”

1957-fc150-fillmore-ca1

1957-fc150-fillmore-ca2

1957-fc150-fillmore-ca3

1957-fc150-fillmore-ca4

 
To Top

2 M-38s Fremont, CO **SOLD**

• CATEGORIES: M-38 This site contains affiliate links for which I may be compensated.

UPDATE: **SOLD** Was $3000.

Only pics of one jeep provided.

“1950 Willy’s Military Jeep 75% complete. Also one 1952 military jeep 100% original and complete titles 3,000 for both or will sell separate.”

1950-m38-fremont-co1 1950-m38-fremont-co2