I’ll be taking the next two nights off. See you next year on the 2nd! Happy New Year!
Monthly Archives: December 2010
Happy 17th Birthday Chris
Over the past year and a half Chris (from Mossy Rock, Wa) and I have been trading emails every-so-often as he works his way through his flat fender project. He recently figured out how to work with some bondo; he also tried his hand at using Herculiner. You can see the results below. It’s a bit of a trial and error process for him, but he’s making good progress.
January 1st is his birthday, so have a great birthday Chris and keep the pics coming!
The Jerry Can Tool Box
Maggie mentioned to me that she was searching for a Jerry Can Tool Box someone built and displayed on line. With a little searching we tracked it down to Jeepforum.com. I’ve included two pics of it below. You can see all the pics here.
1958 CJ-5 Chico, Ca eBay
Hog forwarded this auction. Bidding just ended on this CJ-5 previously owned by Bing Crosby, reaching a high of $5850. I suspect it will be back on eBay at some point.
“Barn stored since 1973. Perfect running condition. Originally used on Rising River Ranch by the Crosby Cattle Co. Owned by Bing Crosby from new until 1973. All original, but seats and turn signal assembly. As you can see in the pictures the cosmetics are not perfect, but are easily fixed. This thing could climb a wall! She’s ready to go and up to date on all paperwork. Pink slip in hand.”
CJ-5 Parts Boise, Id **SOLD**
UPDATE: An eWillys reader bought all the parts.
Ken’s located here in Boise and has a variety of parts for sale and wants them gone!
Complete Fiberglass tub and front clip
Complete 304 Engine W/ Headers, Eldelbrock 4BBL, Mallory Distributor, Aluminium Valve Covers,Flywheel & Clutch.
Radiator
2 Wiring Harness, 1stock, 1aftermarket
Prothane body mount kit, motor mounts, trans mount, complete suspension and steering boot kit, shock boots. (N.I.B.)
Steering Column, Grant steering wheel, Power Steering Gear, Sector shaft.
Heater Assembly (stock)
2 Dashes, 1 with instruments and Cables, The other is painted to match tub
Seat Risers, Driver and Passenger
Front and rear seats (YJ)
1 set new springs
New spring mounts and shackles (full set for front and back)
Spicer 20 T/Case
2 T150 3 speed transmissions in near perfect condition
Roll Bar (stock)
Stainless hard line kit (brake and fuel)
Gas Tank (N.I.B. polyurathane)
Clutch and Brake peddle assy.
Console
Stainless steps
NO FRAME OR AXLES
Here are a variety of pics:
Click below to see more pics ….
1966 CJ-5 Port Crane, NY **SOLD**
UPDATE: **SOLD** Was on $500
This includes a rebuilt engine, though it isn’t installed.
“1966 Jeep with aftermarket solid top, standard on column, 4×4, 4 cylinder, with 6′ MANUAL angle, hydraulic lift plow. This is a project Jeep, does NOT currently run. Needs work, Engine re-built but NOT installed, Needs starter, alternator, battery, etc… to run. This is a cool little Jeep that would make a great winter project.”
1964 CJ-5 Miami, Fl $1000
There might be some value in this project.
“1964 Jeep CJ5, 4 X 4, manual transmission, 4 cylinder, all original. This jeep was sitting for a while and will need some work to get it running. I am firm in the $1,000 price, dont call if you want it cheaper than that. 786-556-3668”
1946 CJ-2A Ramona, Ca $9500
This looks good.
“1946 Willys CJ2A jeep, original 4cyl flathead and 4 spd trans both rebuilt, this jeep had a complete resto a few years ago, have the reciepts to prove it, has wide tires on it, runs like a champ full soft top $9500 obo call 760-518-5510 or email”
1941 Slat Grille MB Las Vegas, Nv **SOLD**
UPDATE: **SOLD** was on eBay
Here’s a slattie project.
“You are bidding on a great restoration project. I am thinning out my collection because I have a few other rare vehicles that I’m in the process of restoring so some toys must go. This one up for auction is a 1941 Willys slat grill. It does have rust in the usual places such as front floors, fuel tank and driver side panel area. The jeep has been media blasted from top to bottom but surface rust is starting due to the fact that it was not primered. I was hoping to start restoration sooner but other projects have forced me to push it aside which is why I am selling. The frame is very solid and has also been blasted. I do have a front bumper and a rear crossmember that will go with the jeep. As can be seen in the pictures, the tail panel has been messed with and will need to be fixed. The jeep comes with a complete MB motor but it is not original to the car as the vin is very high. I do have one front seat that will go with the jeep and a back seat. The jeep does have the original low windshield with the early brass windshield clamps which are hard to find. The jeep also comes with some hard to find parts such as the solid wheels and the original pancake air cleaner. ”
1955 Truck Gowen, Ok No Price
This might make a good project.
“Willys 4 wheel drive truck project. Chassis in excellent condition and body is in good condition for the year.Have flathead 6 motor.The truck came from California so no rust to speak of. Need to see it and then make fair offer.”